MIL-DTL-28837C
-
Aluminum-Alloy 6061-T6 Standard Structural Shapes.
-
Gold for Engineering Uses, Electrodeposited Coatings of.
-
Tin, Electrodeposited Coatings of.
-
Electrodeposited Coatings of Silver for Engineering Use.
-
Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy
Walled Tubing and Basic Shapes.
-
Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and
Ram Extrusion Materials.
-
Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From
Dispersion.
-
Compounds, Molding, Thermosetting.
(Copies of these documents are available from ASTM International, 100 Barr Harbor Drive, West Conshohocken,
PA 19428-2959 or www.astm.org.)
SOCIETY OF AUTOMOTIVE ENGINEERS (SAE) INTERNATIONAL
SAE-AMS2404
-
Plating, Electroless Nickel
SAE-AMS2422
-
Plating, Gold.
SAE-AMS4290
-
Aluminum Alloy, Die Castings 9.5si-0.5mg (360.0-F).
SAE-AMS4291
-
Aluminum Alloy, Die Castings 8.5si-3.5cu (A380.0-F) (See As 1990) As Cast.
SAE-AMS5511
-
Steel, Corrosion-Resistant, Sheet, Strip, and Plate 19 Cr - 9.5 Ni (304L)
Solution Heat Treated.
SAE-AMS-I-23011
-
Iron Nickel Alloys for Sealing to Glasses and Ceramics.
SAE-AMS-QQ-A-250
-
Aluminum and Aluminum-Alloy, Plate and Sheet.
SAE-AMS-QQ-N-290
-
Nickel Plating (Electrodeposited).
SAE-AMS-QQ-S-763
-
Steel Bars, Wire, Shapes, and Forgings; Corrosion Resistant.
SAE-J452
-
Chemical Compositions, Mechanized and Physical Properties of SAE,
Aluminum Casting Alloys, General Information.
(Copies of these documents are available from SAE International, 400 Commonwealth Drive, Warrendale, PA
15096-0001 or www.sae.org.)
2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the
text of this document and the references cited herein (except for related specification sheets), the text of this
document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless
a specific exemption has been obtained.
3. REQUIREMENTS
3.1 Specification sheets. The individual mixer requirements shall be as specified herein and in accordance with
the applicable specification sheets. In the event of any conflict between requirements of this specification and the
specification sheet, the latter shall govern.
3.2 Qualification. Mixers covered by specification sheets furnished under this specification shall be products which
are qualified for listing on the applicable qualified products list at the time set for the opening of bids (see 4.5 and 6.3)
3.3 Material. The material shall be as specified. When a definite material is not specified, a material shall be used
which will enable the mixers to meet the performance requirements of this specification. Acceptance or approval of
any constituent material shall not be construed as a guaranty of the acceptance of the finished product. Unless
otherwise specified (see 3.1), the material shall be selected from the following materials.
a.
Aluminum alloy plates and sheet shall conform to the composition 6061 of ASTM-B209 and SAE-AMS-QQ-
A-250; extruded aluminum alloy shall conform to composition 6063 of ASTM-B241/B241M, or composition
6061 of ASTM-B221. Aluminum bar shall conform to 6061 per ASTM-B221 and ASTM-B241/241M.
3
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business